Modified Shipping Container House Prefabricated House (shs-mc-special014)

• Customization: Available
• Material: Container
• Insulation Layer: Glass Wool/ Mineral Wool/ PU Foam
• Model NO.: shs-mc-special014
• Color: All Color
• Structure: Pre-Welded
• Rusting Proof: Double Layer Painting
• Usage: Warehouse, Villa, Dormitories, Temporary Offices, Workshop, Equipment Cabin
• Certification: ISO, SGS
• Customized: Customized
• Transport Package: Container House Itself
• Specification: ISO
• Trademark: SHS
• Origin: Shanghai
• HS Code: 94060000
• Production Capacity: 30 Modified Container

Product Description

Introduction

Application of Modified Shipping Container House Prefabricated House:

Modified Shipping Container House Prefabricated House is modified from the standard shipping container. 20 feet, modified for office and living. The wall panel is insulated with PU foam. PU foam has the most outstanding insulated affect. Better than mineral woo or glass wool. Especially adapt to the cold area, such as in Russia.

Container Modifications:
Shipping containers have tough bodies. The corrugation panels (roof, sides, and back), floor, purlins, front doors, frame, and rails form an integrated structural skin. They are strong and made to carry floor loads far in excess of what is required for typical home construction. But, when we modify them, cutting holes or penetrating members, they are weakened. High level of modification the shipping container home design calls for, our structural engineer and architect will supply a professional plan.

As we said above, when cutting a shipping container or removing any of the paneling, it's structural integrity is compromised. As an extreme example, consider the removal of all a container's corrugated paneling along the length of one side. Without reinforcement, the container deforms and then fails structurally.
As a general rule, whenever remove portions of the panelized corrugation, steel framing will be required to frame out the opening. In addition, column and roof support will be necessary depending on the size of the opening(s) and roof/wind loads.
Steel cutting, framing, and welding is a large part of shipping container home design and construction. Typically, steel construction is not used much in single family or smaller home design because of expense. Cost of steel vs. Wood/light gauge framing is substantial and the labor cost for steel vs. Carpentry is also higher. To combat this, much of the welding and reinforcing done off-site before setting the containers on site and starting the interior fit-out.

Set and Secure Containers to Foundation and Each Other
When the shipping containers arrive on site, they are crane-lifted one by one onto the foundation, hooked into place, and welded down to marry them completely to the foundation. These heavy-gauge steel containers are so strong- Each is designed to carry 57, 000 pounds- That they need only be fastened at the corners to hold fast, much as they would be on a ship. In the example above, the shipping container bottom corner blocks are welded to steel plates imbedded in the concrete slab to secure the house to the foundation. All corner blocks are welded to each other to secure the containers to themselves.

Install windows, exterior doors, flashing, and any sky lights
Windows are set into openings that were measured and cut prior to delivery of the shipping containers or roughed out on site. All openings for windows and doors should be framed with a steel section. Hollow rectangle sections work the best, but an L section will work as well. Openings for sliding door systems in the end and sidewall panels of a container are common.

Install interior framing, insulation, heating and cooling systems, plumbing, electrical, and rough out all fixtures.
Supertherm insulative coating, is sprayed on both sides of the remaining container walls. Supertherm is a high-performance, four-part ceramic coating that carries an R value of R-19 and adheres to the steel surface of the shipping containers. A ½ - inch plywood floor over the existing ¾ - inch plywood sub-floor is installed. Metal hat channels for wiring are run along the walls and vertical support beams are secured. Metal studs and drywall are used for interior partition walls. Once insulated, the existing container walls are faced in drywall for finishing.

Table I. Safety Factors on Land for Various Stack Heights on Land with Container Corner Post Capacity of 190,480 lbs (86,400 kg)
Number of Containers Stacked on One		Total Height of Stack		Safety Factor on Corner post loading
8		9		1.80
9		10		1.60
10		11		1.44
11		12		1.31
The table shows that we can stack 9-on-1 on land, and maintain a safety factor of greater than 1.5.
Table II. Stack Heights on Land forVarious Detector Densities with Container Corner Post Capacity of 214,290 lbs (97,400 kg)
Number of Containers Stacked on One	Total Height of Stack (m)	Safety Factor on Corner Post Loading
		with payload density = 0.60 g/cc (22,150 kg gross)	with payload density = 0.66 g/cc (24,000 kg gross)	with payload density = 0.75 g/cc (27,150 kg gross)	with payload density = 0.85 g/cc (30,480 kg gross)
8 on 1	23.3	2.20	2.03	1.80	1.60
9 on 1	25.9	1.95	1.80	1.59	1.42
10 on 1	28.5	1.76	1.62	1.43	1.28
11 on 1	31.1	1.60	1.48	1.30	1.16
Conclusion:Stacking ISO containers 10 high on land is reasonable, and stacks as high as 12 may be possible depending on the type of container purchased and on the loading of the container with Off-Axis detector elements. For a final detector design, good engineering practice would require that the corner posts of the selected containers be loaded to failure to more accurately determine the safety factor of the stacked array.

FAQ

1. Are you a factory or a trading company.
We are a factory.

2. What products do you offer.
We offer modular buildings mainly on the types of flatpack container and mofidied container. 

3. What is your payment term.
TT and LC

4. What is your minimum order quantity
For the type of flatpack container is 120 square meters

5. What information should we offer before you quote.
If you have drawing, pls tell us the materials and specifications.
If you don't have drawing, pls tell us the usage and size etc. 

6. Could you please design a new and unique prefab house for me?
Absolutely! We can provide you with not only a construction scheme but landscape design! One-stop service is our outstanding superiority with no doubt.

7. What's your delivery time?
Normally, delivery time is within 30 days after the deposit is received. For large orders, the delivery time should be negotiated as per actual production sechedule.

8. How to control the quality of your product?
First, quality of the design: think about possible problems in advance and provide a high-quality design solution.
Second, quality of the raw material: choose the qualified raw material.
Third. quality of the production: precise manufacturing technique, experienced workers, strict quality inspection.

9. Do you provide on-site installation service?
We provide very detailed installation instruction drawings and videos to ensure smooth installation for customers
We will have installation workers and supervisors on-site as per clients' needs. The fee for the on-site service should be negotiated with clients.

10. How to deal with quality problems?
The warranty is 1 year. Within the warranty period, we will be responsible for all quality problems caused by our production.